Marque	Modele	Autodetection	Maximum Resolution	SUSE Linux Version	Remarque
Acer	AL1715		1280x1024	10.0, 10.2
Acer	AL2021		1600x1200	10.0, 10.1
Acer	AL922		1280x1024 (probably much more)	9.2, 9.3, 10.0	in Sax2's monitor database as "ABO ACER AL922" since 10.0, horizontal:30-80 vertical:43-75
Benq	FP567		1024x768	10.0
Dell	2000FP		1600x1200	10.0, 10.2
Dell	2001FP		1600x1200	10.0, 10.1	Select the "DELL 2001FP (DIGITAL) in YaST config.
Dell	2001FP		1900x1200	10.0	VertRefresh incorrect, should be 56-60
IC power	cm2015		1024x768	10.0	plug it in and go.
Eizo [1]	FlexScan S1901		1280x1024@60Hz	10.1
Eizo [2]	FlexScan S1910		1280x1024@60Hz	10.1
Eizo [3]	FlexScan S2110W		1680x1050@60Hz	10.1
HP	1702	at boot, but not as to the model and resolution	1280x1024	10.0, 10.1	Used generic LCD settings for 1280x1024. Does not allow rotate to portrait view. Works fine besides that
Hyundai	ImageQuest Q17		1280x1024	10.0
Iiyama	AS4316UTC		1280x1024	10.0
Iiyama	AS4315		1600x1900	10.2	Works just fine, @ 75 mghz, Aspect 4/5
Lucky Goldstar	Flatron 17		1280x1024	10.0
Lucky Goldstar	Flatron M203WX		1680x1050	10.0	Requires video card with card driver which supports this mode
MITSUBISHI	RDT178S		1280x1024	10.0	horizontal:31-81 vertical:56-75
NEC	MultiSync LCD1970NXP		1280x1024	10.0, 10.1, 10.2	horizontal:30-81 vertical:50-75
Samsung	712N		1280x1024	10.0
Samsung	930B		1280x1024	10.2	Horizontal: 30-81 kHz Vertical: 56-75 kHz
Yusmart	198IP	workable from previous CRT settings at boot	1440x900	10.1/10.2	Configure via Yast. Select generic LCD 1440x900. I had nVidia drivers installed for my graphics
Sharp	LL-M17W1U		1280x768	10.1	Autodected as a generic LCD. Inserting the utility disk and doing further configuration in Yast allows autodetection of the model as well
ViewSonic	VA902b		1280x1024	10.1	After install and reboot, KDE outputs an unsupported signal. FYI: Monitor supports these Refresh Rates: Horizontal: 30~82kHz, Vertical: 50~85Hz. I found a solution... Will add it soon

[modifier]

CRT Moniteurs

Marque	Modele	Resolution	SUSE Linux Version	Remarque
Envision	EN-780e	1024x768	10.0, 10.1	Refresh rate defaulted to 88Hz, max supported by monitor is 85. I didn't realize this, until over time the monitor was dying. First the display would jump from taking up the full screen to taking up more, or less than the full screen (the sides being expaded or cut off). Then one day, the monitor didn't work at all on this configuration, but did work under proper configuration.
LG	F700B	1024x768	10.0	VertRefresh and HorizSync are incorrect, should be 50-160 for VertRefresh and 30-71 for HorizSync. Refresh rate is also incorrect, should be 85Hz for optimal 1024x768 resolution. I had to put # before "UseModes "Modes[0]"" line in xorg.conf to fix refresh rate.
Philips	107T5	1024x768	10.1	No problems noted.
Samsung	SM997MB	1280x1024@73Hz 1920x1200@63Hz	10.0	lower resolutions are at 73Hz too, but maybe it can be configured somehow. (SM stands for SyncMaster)
Sony	CDP-420GS	1152x864@75Hz	9.2

[modifier]

External Links

Novell SUSE Linux - Hardware Compatibility List

Novell SUSE Linux Certified Hardware

Cet article a besoin d'être complété. Si vous pouvez y participer, merci de le faire en accord avec le Guide pour le style.
Si vous cherchez quelque chose à faire, regardez les autres Pages à compléter

Récupérée de « http://fr.opensuse.org/Compatibilit%C3%A9_mat%C3%A9rielle/Ecrans »

Catégories de la page: A traduire | Hardware Compatibility List | Pages à compléter

Le contenu de cette page et des autres pages du wiki est mis en ligne par des membres de la communauté qui n'agissent pas pour le compte ou à la demande de la société Novell, quelle que soit par ailleurs leur éventuelle affiliation avec Novell
This site uses the YAML CSS framework.
À propos de openSUSE | Avertissements | Feedback
Dernière modification de cette page le 2 mai 2008 à 19:08. Cette page a été consultée 1099 fois.